
SammySam
MAIL-IN ALTERATIONS — SEWSEND™
Sammy’s fitting guides
Measure and mark your garment at home
Pick your garment below. Each guide shows what to measure, how to mark it and which photos to take, so our tailors can quote your alteration accurately.
Before you start
- Never cut, trim or sew your garment yourself. Only mark it.
- Mark with removable tailor’s chalk, fabric clips or safety pins (not straight pins, which can fall out in the mail). Test chalk on an inside seam first.
- Wear the underlayers and shoes you’ll wear with the garment, stand straight and relax.
- Some alterations — letting out, shoulder work, bridal gowns, beading or lace — can only be confirmed when we inspect the garment. Measuring at home helps us quote, but can’t guarantee the final fit.
Using a soft measuring tape
- Keep the tape flat and straight — not twisted, not pulled tight.
- Start exactly at 0 and read where the measurement ends.
- Choose inches or centimeters and use the same unit everywhere in your request.
- Measure twice. Write the number down right away.
Pants & jeans — hem, waist and taper
- Put the pants on with your shoes. Fold the hem under to the length you want.
- Mark the fold with chalk, or two safety pins per leg (front and back).
- Take the pants off and measure the finished inseam: from the crotch seam down the inside leg to your mark. Tell us how much to remove or add.
- Original jeans hem? Say so — we keep the factory hem.
- Waist: pin the extra fabric at the center back, then measure your current and desired waist flat across the waistband (× 2).
Photos: front, back and a close-up of the marked hem.
Dresses, formal & bridal gowns
- Wear the shoes and undergarments you’ll wear with the dress.
- Shorten: mark the finished hem at the center front; measure the current and desired length from the top of the shoulder to the hem.
- Take in or let out: measure your bust, waist and hips with the tape snug, not tight; pin evenly along both side seams. Letting out depends on the seam allowance inside — we confirm it when we see the dress.
- Shoulders: pin the strap or shoulder seam where it should sit, and add a photo of the dress being worn.
- Tell us about lining, lace, beading, sequins, boning, layers, corsets or zippers. If we ask, send photos of the inside seams.
Bridal and heavily embellished gowns always get a special review before we quote.
Suits, jackets & coats
- Button the jacket and let your arms hang naturally.
- Sleeves: fold the cuff under to where it should end (about ½ in past the wrist bone) and pin it. Measure from the shoulder seam to the fold.
- Waist: pin the extra fabric evenly at the back seam or side seams.
- Trousers: follow the pants guide.
- Add photos of the garment worn from the front, side and back.
Shoulder reconstruction and length changes are major work: they get a special review, and a final fit can’t be guaranteed from body measurements alone.
Shirts & blouses
- Take in: turn the shirt inside out and pin evenly along both side seams — the same amount on each side.
- Sleeves: pin the cuff where it should end; measure from the shoulder seam.
- Length: mark the new hem with chalk at the front and back.
Repairs, zippers & buttons
- Mark the damaged spot with a safety pin (outside the hole, never through it).
- Measure the size of the damage and say whether fabric is missing.
- For zippers, tell us the length and color; for buttons, how many and their size.
- Take a close-up photo of the damage, and use “Mark up photo” to circle it.
Photographing your garment
- Use daylight or a bright room; lay the garment flat or hang it up so all of it is visible.
- Take the front, the back, and a close-up of the area to alter with your marks visible.
- After uploading, tap “✎ Mark up photo” to draw arrows, lines or circles and add short notes. Your original photo is kept unchanged.
- Leave out personal documents, cards and anything unrelated.
Send it. We alter it. We send it back.
Request my free quote